Work out which kind of corrosion you have before anyone fixes anything. Blistered paint, white powder and pitting on an aluminum drive near stainless parts is galvanic corrosion, which works slowly and is repaired by sanding to sound metal, priming, repainting and renewing the anodes. Damage that shows up in days points to stray current from an electrical fault, and that fault has to be found first. Once a housing is porous, weeping gear lube or eaten through, replacing the gearcase or drive usually beats repairing it. If you want a tech to look at it, you can find corrosion repair pros by location.
Which type of corrosion are you looking at?
Galvanic corrosion is the slow one. It starts when different metals, for example an aluminum gearcase next to a stainless steel propeller, are both submerged in water that conducts electricity. Salt water is the worst, but brackish water, very mineral-rich fresh water and polluted water also conduct well, and warmth makes it worse. Early signs are paint blistering on sharp edges below the waterline, then white powder, then deep pitting.
Stray-current corrosion is the fast one. It usually comes from a faulty connection touching a submerged metal, often a wire run near bilge water. Even a 12-volt source can corrode a propeller, shaft or sterndrive severely within hours or days. Aluminum lower units on outboards and pod drives are particularly vulnerable.
| Galvanic | Stray current |
|---|---|
| Cause | Dissimilar metals in conductive water |
| Speed | Slow, gradual |
| What it looks like | Blisters, white powder, pitting, often near stainless parts |
| Do anodes help? | Yes, they are the first line of defense |
| Actual fix | Surface repair, new anodes, isolation or protection |
| Who handles it | You or an engine tech |
Paint that has worn through to bare metal, especially on a skeg that drags over sand or gravel, makes either type worse, because bare aluminum corrodes faster next to a stainless prop.
What the repair involves, from paint to parts
Light damage is a surface job. Remove the prop, clean off oil, wax, grease and salt, then sand pitted or blistered areas with 180 or 220 grit, prime, and apply several thin coats of paint rather than one heavy one. Never use steel wool, because it leaves steel fragments in the surface that can rust later. Below the waterline, use epoxy filler, since polyester and car fillers absorb water.
Bigger areas call for grit blasting, which should be done by a pro using aluminum-compatible grit; copper slag abrasives promote serious corrosion.
With stray current, the metalwork comes second. The tech traces the wiring or bonding fault, repairs it to ABYC standards, then deals with the damaged part.
What drives the price of corrosion repair
Price follows engine type (outboards are generally easier to reach than inboards, which sit in tight compartments), how deep the corrosion goes, whether the job is a part swap or a teardown, and whether parts still exist for an older unit. Two boats with the same symptom can need very different work, so a diagnosis has to come before a number. Our guide to what drives the price and how to get accurate estimates goes wider.
Anodes are the smallest bill. A Mercury replacement kit with mounting hardware sold for about $75 in 2012, so treat that as a floor from an old article, not today's price. Labor on seized or hard-to-reach parts costs most, and older drives used in salt water and not flushed and serviced regularly can become impossible to service without breaking parts.
DIY fix, pro job, or not worth repairing?
| What you see | Path |
|---|---|
| Paint worn to bare metal, light pitting or blisters, small area | DIY touch-up |
| Large corroded areas, anything needing blasting | Professional repair |
| Metal lost within days | Pro with electrical skills, before any cosmetic work |
| Porous housing, lube oozing through the aluminum, exposed bearing carrier | Replace the gearcase or drive |
| Seized drive that can't come apart, parts unavailable | Replace |
If you do the touch-up yourself, work with the engine off and cool, and follow the product instructions. Some manufacturers require an authorized dealer to install certain repair kits.
Stopping corrosion from coming back
Flush and rinse after every saltwater run, and replace anodes when they wear to about half their original size, using the type suited to your water. Keep the drive down at the mooring so the anodes stay submerged. On shore power, add a galvanic isolator, and keep bonding connections clean and tight.
How to judge a pro for corrosion work
Ask how the tech will find the cause before quoting metalwork. Good answers include a hull potential test to check corrosion protection, and measuring current through the bonding bus bar (any current there means stray current), plus wiring repairs to ABYC standards. If the quote covers only paint and anodes, ask what test ruled out stray current.
Then ask what the diagnosis is, which parts are involved, whether the quote is flat-rate or hourly, and what happens if more turns up once the engine is opened. On Boatwork you describe the job and choose which independent pros to contact; you get estimates only from them. Check that a pro's profile lists marine electrical work before booking a stray-current job.
Next step
To compare diagnoses and quotes for your own engine or drive, start on Boatwork and choose the pros you want to hear from.
Related pages and posts
- Boat engine corrosion repair Services | Find Marine Pros | Boatwork
- Boat Engine Repair Cost: Ranges by Engine Type
- Boat Engine Repair Cost: What Drives the Price and How to Get Accurate Estimates
References
- Corrosion Evasion, Part 1: Preventing Galvanic, Stray-Current Corrosion - Professional BoatBuilder: An IBEX Technical Journal
- Corrosion, Part 2: Stray Current | BoatTEST
- Quick Tip: How to Touch Up Mercury Gearcase Paint | Mercury Marine | USA
- How To Repair Painted Aluminium Zinc Galvanised Steel Thats Corroding | Bw028 | Interlux
- Top Three Reasons to Replace Your Sterndrive
- Preventing Corrosion - Boat Maintenance Tips | Mercury Marine | USA
- Mercury Precision MerCathode: Actively Fighting Galvanic Corrosion | Mercury Marine | USA
- Anodes for Outboards and Outdrives - Boat Trader Blog



